manualshive.com logo in svg

Cisco UCS C200, Installation And Service Manual

Share
Download
Cisco UCS C200 Installation And Service Manual Download Page 16

   

1-2

Cisco UCS C200 Server Installation and Service Guide

OL-20732-02

Chapter 1      Overview

  

Figure 1-2

Front Panel Features, Small Form Factor

Caution

Do not use the 

Reset

 button. This button is for development debugging only. This button will reset 

memory and CPU settings to the defaults.

1

KVM console connector

10

Hard drives (up to 8)

2

Reset button

1

1.

See the following caution.

11

Hard drive fault LED

3

Power supply fault LED

12

Hard drive activity LED

4

Memory fault LED

13

Optional DVD module

5

CPU fault LED

14

DVD activity LED

6

Network activity LED

15

Power button/Power status LED

7

System fault LED

16

Locator button/LED

8

Locator button/LED

17

Reset button

2

2.

See the following caution.

9

Power button/Power status LED

18

System fault LED

-A-

1

10

11

2

3

4

5

6

7

8

12

9

18

14

13

17

16

15

310369

Summary of Contents for UCS C200













































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands