Cisco uBR924 Troubleshooting Tips Download Page 42

Page: 42 / 74

show controllers cable-modem mac

Cisco IOS Release 12.0(5)T

The following example indicates that an event in the cable interface driver caused the interface to
reset. This often occurs because a shut or clear command is currently being issued on the interface.

uBR924#

show controllers cable-modem 0 mac resets

527986.444 CMAC_LOG_RESET_FROM_DRIVER

528302.042 CMAC_LOG_RESET_FROM_DRIVER

528346.600 CMAC_LOG_RESET_FROM_DRIVER

528444.494 CMAC_LOG_RESET_FROM_DRIVER

Table 6

Possible but Uncommon Cable Interface Reset Causes

Message

Description

CMAC_LOG_RESET_CONFIG_FILE_PARSE_FAILED

The format of the DOCSIS configuration file acquired
from the TFTP server is not acceptable.

CMAC_LOG_RESET_LOSS_OF_SYNC

Synchronization with the CMTS has been lost (SYNC
messages are not being received).

CMAC_LOG_RESET_T4_EXPIRED

Maintenance ranging opportunities for this
Cisco uBR924 are not being received from the CMTS.

CMAC_LOG_RESET_DHCP_WATCHDOG_EXPIRED

The DHCP server took too long to respond.

CMAC_LOG_RESET_TOD_WATCHDOG_EXPIRED

The Time Of Day server took too long to respond.

CMAC_LOG_RESET_PRIVACY_WATCHDOG_EXPIRED

The baseline privacy exchange with the CMTS took too
long.

CMAC_LOG_RESET_CHANGE_US_WATCHDOG_EXPIRED

The Cisco uBR924 was unable to transmit a response to a
UCC-REQ message.

CMAC_LOG_RESET_SECURITY_WATCHDOG_EXPIRED

The “full security” exchange with the CMTS took too
long.

CMAC_LOG_RESET_CONFIG_FILE_WATCHDOG_EXPIRED

The TFTP server took too long to respond.

CMAC_LOG_RESET_ALL_FREQUENCIES_SEARCHED

All downstream frequencies to be searched have been
searched.

Note

This message indicates that downstream

frequencies were found, but the Cisco uBR924 failed to
acquire a downstream lock.

CMAC_LOG_RESET_T2_EXPIRED

Initial ranging opportunities are not being received.

CMAC_LOG_RESET_T3_RETRIES_EXHAUSTED

The CMTS failed too many times to respond to a
RNG-REQ message.

Note

After 16 T3 timeouts, the Cisco uBR924 will reset

the cable interface.

CMAC_LOG_RESET_RANGING_ABORTED

The CMTS commanded the Cisco uBR924 to abort the
ranging process.

CMAC_LOG_RESET_NO_MEMORY

The Cisco uBR924 has run out of memory.

CMAC_LOG_RESET_CANT_START_PROCESS

The Cisco uBR924 was unable to start an internal process
necessary to complete ranging and registration.

CMAC_LOG_RESET_CONFIG_FILE_READ_FAILED

The reading of the configuration file from the TFTP
server failed.

Note

The file might not exist, or it might have incorrect

permissions.

CMAC_LOG_RESET_AUTHENTICATION_FAILURE

The Cisco uBR924 failed authentication as indicated in a
REG-RSP message from the CMTS.

Summary of Contents for uBR924











































































Search results

Summary of Contents for uBR924

Reviews:

Related manuals for uBR924

Brands by name

Popular brands

Cisco uBR924, Troubleshooting Tips

Search results

Summary of Contents for uBR924

Reviews:

Related manuals for uBR924

Brands by name

Popular brands