background image

4

RSP4+ Bootflash Memory Upgrade to 16MB Installation and Configuration Guide

78-12288-02

Installation Requirements

Tools and Parts Required

You need the following tools and parts to install or upgrade the bootflash SIMM:

Number 1 Phillips and a 3/16-inch flat-blade screwdriver

ESD-prevention equipment or disposable grounding wrist strap included with all Cisco products

Antistatic mat, foam pad, or bag for the removed SIMM

If you need additional equipment, contact a service representative for ordering information.

Safety Guidelines

Following are safety guidelines that you should follow when working with any equipment that connects
to electrical power or telephone wiring.

Safety Warnings

Safety warnings appear throughout this publication in procedures that, if performed incorrectly, may
harm you. A warning symbol precedes each warning statement.

Warning

This warning symbol means danger. You are in a situation that could cause bodily
injury. Before you work on any equipment, be aware of the hazards involved with
electrical circuitry and be familiar with standard practices for preventing accidents.
To see the translations of the warnings that appear in this publication, refer to the
Regulatory Compliance and Safety Information document that accompanied this
device.

Waarschuwing

Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk
letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich
bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de
hoogte te zijn van standaard maatregelen om ongelukken te voorkomen. Voor
vertalingen van de waarschuwingen die in deze publicatie verschijnen, kunt u het
document

Regulatory Compliance and Safety Information (Informatie over naleving

van veiligheids- en andere voorschriften) raadplegen dat bij dit toestel is ingesloten.

Varoitus

Tämä varoitusmerkki merkitsee vaaraa. Olet tilanteessa, joka voi johtaa
ruumiinvammaan. Ennen kuin työskentelet minkään laitteiston parissa, ota selvää
sähkökytkentöihin liittyvistä vaaroista ja tavanomaisista onnettomuuksien
ehkäisykeinoista. Tässä julkaisussa esiintyvien varoitusten käännökset löydät
laitteen mukana olevasta

Regulatory Compliance and Safety Information -kirjasesta

(määräysten noudattaminen ja tietoa turvallisuudesta).

Summary of Contents for RSP4+





















Reviews: