Cisco Nexus 36180YC-R Hardware Installation Manual Download Page 40

Page: 40 / 42

Fan LEDs

This table provides information about fan LEDs for Cisco Nexus 3000 Series switches.

Description

Status

LED

Component

All diagnostics pass. The module is operational.

Solid on
(green)

Status

Fan

The module is not receiving power.

Off

The module is booting or running diagnostics.

Solid on
(amber)

If the module fails during an initial reset, the LED
continues to blink and the module does not come online.

The module has a runtime failure and is brought offline.

Blinking
(amber)

Power Supply LEDs

This table provides information about power supply LEDs for Cisco Nexus 3000 Series switches.

Description

Status

LED

Component

Power supply is on and okay.

Solid on

OK (green)

Power supply

3.3 voltage standby (VSB) is on but the power supply
unit is not powering the other modules.

Blinking

No power to the power supply.

Off

Power supply failure, overvoltage, overcurrent, or
overheating.

Solid on

FAULT (amber)

Power is present, 3.3 VSB on, and the power supply is
off.

PSU fan rotor is not functioning normally.

Blinking

Operating normally.

Off

Cisco Nexus 3600 Hardware Installation Guide

LEDs

Fan LEDs

Summary of Contents for Nexus 36180YC-R











































Search results

Summary of Contents for Nexus 36180YC-R

Reviews:

Related manuals for Nexus 36180YC-R

Brands by name

Popular brands

Cisco Nexus 36180YC-R, Hardware Installation Manual

Search results

Summary of Contents for Nexus 36180YC-R

Reviews:

Related manuals for Nexus 36180YC-R

Brands by name

Popular brands