Cisco NCS 540 Series Command Reference Manual Download Page 10 | Manualshive

Page: 10 / 84

background image

class-map

To define a traffic class and the associated rules that match packets to the class, use the

class-map

command

in XR Config mode. To remove an existing class map from the router, use the

no

form of this command.

class-map

[

type [traffic | qos]

]

[match-all] [match-any] class-map-name

no class-map

[

type [traffic | qos

]

]

[match-all] [match-any] class-map-name

Syntax Description

(Optional) Specifies a quality-of-service (QoS) class-map.

type qos

(Optional) Specifies traffic type class-map.

traffic

(Optional) Specifies a match on all of the match criteria.

match-all

(Optional) Specifies a match on any of the match criteria. This is the default.

match-any

Name of the class for the class map. The class name is used for the class map and to
configure policy for the class in the policy map. The class name can be a maximum of
63 characters, must start with an alphanumeric character, and in addition to alphanumeric
characters, can contain any of the following characters: . _ @ $ % + | # : ; - =

class-map-name

Command Default

Type is QoS when not specified.

Command Modes

XR Config mode

Command History

Modification

Release

This command was introduced.

Release 6.0

Usage Guidelines

The

class-map

command specifies the name of the class for which you want to create or modify class map

match criteria. Use of this command enables class map configuration mode in which you can enter any

match

command to configure the match criteria for this class. Packets arriving on the interface are checked against
the match criteria configured for a class map to determine if the packet belongs to that class.

These commands can be used in a class map match criteria for the ingress direction:

•

match access-group

•

match [not] dscp

•

match [not] mpls experimental topmost

•

match [not] precedence

•

match [not] protocol

Task ID

Operations

Task
ID

read,
write

qos

Modular QoS Command Reference for Cisco NCS 5500 Series and Cisco NCS 540 Series Routers

4

QoS Classification Commands

class-map

«
...
8
9
10
11
12
...
»

Summary of Contents for NCS 540 Series





















































































Reviews:

No comments

Related manuals for NCS 540 Series

IntelliJack NJ200

Brand: 3Com Pages: 4

Brand: Patton electronics Pages: 2

ipRocketLink 3086FR

Brand: Patton electronics Pages: 6

Brand: Patton electronics Pages: 16

Brand: Patton electronics Pages: 51

Brand: CSS Pages: 2

Brand: Lorex Pages: 186

Brand: Macsense Pages: 39

Brand: Justec Pages: 61

Brand: EVOC Pages: 57

Octopus G Series

Brand: TwinMOS Pages: 29

Brand: 1&1 Pages: 32

WNFB-265AXI(BT)

Brand: Sparklan Pages: 14

Brand: CalAmp Pages: 115

Brand: ADTRAN Pages: 20

Brand: ZyXEL Communications Pages: 66

Brand: Lantech Pages: 20

Brand: socomec Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands