Cisco N9K-C93360YC-FX2 Hardware Installation Manual Download Page 62

Page: 62 / 72

Switch Dimensions

Height

Depth

Width

Switch

3.38 inches (8.59 cm) (2
RU)

24.14 inches (61.31
cm)

17.4 inches (44.2 cm)

Cisco Nexus 93360YC-FX2

Switch and Module Weights and Quantities

Quantity

Weight per Unit

Component

27.4 lb (12.4 kg)

Cisco Nexus 93360YC-FX2
Chassis (N9K-C93360YC-FX2)

—

1.3 lb (0.59 kg)

Fan Module

– Port-side exhaust (blue)
(NXA-FAN-160CFM-PE)

– Port-side intake (burgundy)
(NXA-FAN-160CFM-PI)

2 (1 for operations and 1 for
redundancy)

—

2.64 lb (1.2 kg)

Power Supply module

– 1200-W AC port-side exhaust
(blue) (NXA-PAC-1200W-PE)

– 1200-W AC port-side intake
(burgundy) (NXA-PAC-1200W-PI)

– 1200-W HVAC/HVDC
dual-direction (white)
(N9K-PUV-1200W)

– 930-W DC port-side exhaust
(blue) (NXA-PDC-930W-PE)

– 930-W DC port-side intake
(burgundy) (NXA-PDC-930W-PI)

Transceiver and Cable Specifications

To determine which transceivers, adapters, and cables are supported by this switch, see

https://www.cisco.com/

c/en/us/support/interfaces-modules/transceiver-modules/products-device-support-tables-list.html

To see the transceiver specifications and installation information, see

https://www.cisco.com/c/en/us/support/

interfaces-modules/transceiver-modules/products-device-support-tables-list.html

Cisco Nexus 93360YC-FX2 NX-OS Mode Switch Hardware Installation Guide

System Specifications

Switch Dimensions

Summary of Contents for N9K-C93360YC-FX2









































































Search results

Summary of Contents for N9K-C93360YC-FX2

Reviews:

Related manuals for N9K-C93360YC-FX2

Brands by name

Popular brands

Cisco N9K-C93360YC-FX2, Hardware Installation Manual

Search results

Summary of Contents for N9K-C93360YC-FX2

Reviews:

Related manuals for N9K-C93360YC-FX2

Brands by name

Popular brands