Cisco N9K-C93360YC-FX2 Hardware Installation Manual Download Page 10

Page: 10 / 72

930-W DC power supply support 1+1 redundancy requires both of the following
conditions:

• Ambient temperature of 104°F (40

℃

) or less and

• Use of 3.5 W QSFP+ transceivers or passive QSFP cables

With higher temperatures or other optics, the switch requires both power supplies
for operations without power redundancy.

Note

Both power supplies are the same type. Do not mix AC, DC, or HVAC/HVDC
power supplies.

Note

All fan modules and power supplies must use the same airflow direction. If you
are using the 1200-W HVAC/HVDC power supplies, those power supplies
automatically use the same airflow direction as used by the fan modules.

Note

Deployment Scheme for SFP-10G-T-X Transceivers

The following figure shows the maximum configuration density of SFP-10G-T-X SFP+ transceivers for this
switch.

The following figure shows the switch features on the port side of the chassis.

Cisco Nexus 93360YC-FX2 NX-OS Mode Switch Hardware Installation Guide

Overview

Summary of Contents for N9K-C93360YC-FX2









































































Search results

Summary of Contents for N9K-C93360YC-FX2

Reviews:

Related manuals for N9K-C93360YC-FX2

Brands by name

Popular brands

Cisco N9K-C93360YC-FX2, Hardware Installation Manual

Search results

Summary of Contents for N9K-C93360YC-FX2

Reviews:

Related manuals for N9K-C93360YC-FX2

Brands by name

Popular brands