Cisco N9K-C9332D-GX2B Hardware Installation Manual Download Page 44

Page: 44 / 50

Description

Cable

India AC Type A Power Cable

CAB-TA-IN

Israel AC Type A Power Cable

CAB-TA-IS

Japan Cabinet Jumper Power Cord, 250 VAC 12A, C14-C15

CAB-C15-CBN-JP

Cabinet Jumper Power Cord, 250 VAC 13A, C14-C15 Connectors

CAB-C15-CBN-EURA

Cabinet Jumper Power Cord, 250 VAC 10A, C14-C15 Connectors

CAB-C15-CBN-CK

Regulatory Standards Compliance Specifications

The following table lists the regulatory standards compliance for the switch.

Table 1: Regulatory Standards Compliance: Safety and EMC

Description

Specification

Products should comply with CE Markings according to directives 2004/108/EC
and 2006/95/EC.

Regulatory compliance

• CAN/CSA-C22.2 No. 60950-1 Second Edition

• EN 60950-1 Second Edition

• IEC 60950-1 Second Edition

• AS/NZS 60950-1

• GB4943

Safety

• 47CFR Part 15 (CFR 47) Class A

• AS/NZS CISPR22 Class A

• CISPR22 Class A

• EN55022 Class A

• ICES003 Class A

• VCCI Class A

• EN61000-3-2

• EN61000-3-3

• KN22 Class A

• CNS13438 Class A

EMC: Emissions

Cisco Nexus 9332D-GX2B NX-OS Mode Switch Hardware Installation Guide

System Specifications

Regulatory Standards Compliance Specifications

Summary of Contents for N9K-C9332D-GX2B



















































Search results

Summary of Contents for N9K-C9332D-GX2B

Reviews:

Related manuals for N9K-C9332D-GX2B

Brands by name

Popular brands

Cisco N9K-C9332D-GX2B, Hardware Installation Manual

Search results

Summary of Contents for N9K-C9332D-GX2B

Reviews:

Related manuals for N9K-C9332D-GX2B

Brands by name

Popular brands