Cisco MDS 9396T Hardware Installation Manual Download Page 67

Page: 67 / 68

Date

Time

Verified By

Planning Activity

Task No.

Electromagnetic interference
(EMI) evaluation:

• Distance limitations for

signaling

• Site wiring

• RFI

levels

1. Verify that the power supply installed in the chassis has a dedicated AC source circuit.

2. UPS = uninterruptible power supply.

3. RFI = radio frequency interference.

Contact and Site Information

Use the following worksheet to record contact and site information.

Table 10: Contact and Site Information

Contact person

Contact phone

Contact E-Mail

Building/site name

Data center location

Floor location

Address (line 1)

Address (line 2)

City

State

Zip code

Country

Chassis and Network Information

Use the following worksheets to record chassis and network information.

Contract Number :

Cisco MDS 9396T Multilayer Fabric Switch Hardware Installation Guide

Site Planning and Maintenance Records

Contact and Site Information

Summary of Contents for MDS 9396T





































































Search results

Summary of Contents for MDS 9396T

Reviews:

Related manuals for MDS 9396T

Brands by name

Popular brands

Cisco MDS 9396T, Hardware Installation Manual

Search results

Summary of Contents for MDS 9396T

Reviews:

Related manuals for MDS 9396T

Brands by name

Popular brands