Cisco MDS 9396T Hardware Installation Manual Download Page 44 | Manualshive

Page: 44 / 68

background image

Before you begin

• A fan slot must be open and ready for the new fan module to be installed.

• You must have a new fan module on hand and ready to install within one minute of removing the original

fan module if the switch is operating.

• The new fan module must have the same airflow direction as the other fan and power supply modules

installed in the switch. All of these modules must have either red coloring (port-side intake airflow) or
they must all have blue coloring (port-side exhaust airflow).

Step 1

Slide the fan module into the fan module bay.

Step 2

Tighten the fan module captive screw.

Step 3

Verify that the Status LED turns on and becomes green.

Removing a Fan Module

The fan module is designed to be removed and replaced while the system is operating without presenting an
electrical hazard or damaging the system.

The Cisco MDS 9000 Family has internal temperature sensors that can shut down the system if the temperature
at different points within the chassis exceed certain safety thresholds. To accurately monitor the system
temperature, the temperature sensors require sufficient airflow through the chassis. In the event that a fan
module is removed from the chassis and the airflow is reduced, the system will bypass the temperature sensor
information and shut down after five minutes to prevent undetected overheating. However, the switches will
shut down sooner if the major temperature threshold is exceeded.

Caution

While removing the fan module, keep your hands and fingers away from the spinning fan blades. Let
the fan blades completely stop before you remove the fan module.

Statement 258

Note

To remove the existing fan module, follow these steps:

Step 1

Locate the fan module in the back of the switch.

Step 2

Loosen the fan module captive screw.

Step 3

Grasp the fan module handle and pull it outward.

Step 4

Once the fan blades have stopped spinning, remove the fan module completely from the fan bay.

Cisco MDS 9396T Multilayer Fabric Switch Hardware Installation Guide

38

Installing the Cisco MDS 9396T Switch

Removing a Fan Module

«
...
42
43
44
45
46
...
»

Summary of Contents for MDS 9396T





































































Reviews:

No comments

Related manuals for MDS 9396T

Brand: Thinklogical Pages: 27

Brand: AbleNet Pages: 12

BONANZA ACCU-SIM V35B

Brand: A2A Simulations Pages: 112

FRIENDLYNET FS4116R

Brand: Asante Pages: 6

Brand: A-Neuvideo Pages: 16

Brand: Black Box Pages: 9

Brand: Elements Pages: 2

Brand: Kobold Pages: 23

Brand: Crestron Pages: 36

LMP-0602 24-V2 Series

Brand: ANTAIRA Pages: 2

Brand: Key Digital Pages: 20

Brand: Edimax Pages: 8

Extricom AT-EXLS-3000

Brand: Allied Telesis Pages: 120

Brand: Dwyer Instruments Pages: 4

Brand: 3onedata Pages: 4

tekmarNet 4 User Switch 481

Brand: Tekmar Pages: 12

Brand: Yacoub Automation GmbH Pages: 45

WL-CPE2G24D-075

Brand: Mach Power Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands