Home
/
Cisco
/
IP Phone 6841
/
Administration Manual

Cisco IP Phone 6841, Administration Manual

Share

Page: 182 / 240

Cisco IP Phone 6841 Administration Manual Download Page 182

Description

Parameter

If a resync operation fails because the IP Telephony device was unable
to retrieve a profile from the server, if the downloaded file is corrupt,
or an internal error occurs, the device tries to resync again after a time
specified in seconds.

If the delay is set to 0, the device does not try to resync again following
a failed resync attempt.

Default: 3600

Resync Error Retry Delay

Forced resync delay typically takes place when it is time to a resync
and you are in an active call. For example, if you set 5 minute for
Periodic Resync and you place a call right after the resync, the resync
happens while you are 6 minutes into the call (normal time of Resync
+ Forced Resync Delay).

Default: 14400

Forced Resync Delay

Controls requests for resync operations via a SIP NOTIFY event sent
from the service provider proxy server to the IP Telephony device. If
enabled, the proxy can request a resync by sending a SIP NOTIFY
message containing the Event: resync header to the device.

Default: Yes

Resync From SIP

Enables or disables the resync operation after any upgrade occurs. If
Yes is selected, sync is triggered.

Default: Yes

Resync After Upgrade Attempt

If the logical equation in these parameters evaluates to FALSE, Resync
is not triggered even when Resync On Reset is set to TRUE. Only
Resync via direct action URL and SIP notify ignores these Resync
Trigger.

Default: Blank

Resync Trigger 1

Resync Trigger 2

A resync is considered unsuccessful if a requested profile is not received
from the server. This can be overridden by this parameter. When it is
set to

No

, the device accepts a

file-not-found

response from the server

as a successful resync.

Default: Yes

Resync Fails On FNF

Remote configuration profile rules evaluated in sequence. Each resync
operation can retrieve multiple files, potentially managed by different
servers.

Default: /$PSN.xml

Profile Rule

Profile Rule B

Profile Rule C

Profile Rule D

Cisco IP Phone 6800 Series Multiplatform Phones Administration Guide

168

Cisco IP Phone Web Page

«
...
180
181
182
183
184
...
»

Summary of Contents for IP Phone 6841

















































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands