Cisco GSS-4492R-K9 Administration Manual Download Page 72

Page: 72 / 230

Chapter 2 Managing the GSS from the CLI

Replacing GSS Devices in Your GSS Network

2-38

Cisco Global Site Selector Administration Guide

OL-10410-01

gss3.example.com#

gss disable

This command removes all previously configured DNS rules and keepalives.

If this is a new GSS device, configure basic network connectivity following
the procedures outlined in the

Cisco Global Site Selector Getting Started

Guide

, Chapter 3, Setting Up Your GSS.

Save your configuration changes to memory by entering the following
command:

gss3.example.com#

copy running-config startup-config

If this is an existing GSS device, delete it from your GSS network through the
primary GSSM GUI. See the

“Deleting GSS Devices”

section in

Chapter 1,

Managing GSS Devices from the GUI

If you want to use the same hostname and IP address of the failed standby
GSSM, determine if you have a backup of the startup-configuration file for
that device as follows:

•

If yes, reload the backup copy of the GSS device startup configuration
settings (see the

“Saving the startup-config and running-config Files”

section).

•

If no, reenter the platform configuration following the procedures outlined in
the

Cisco Global Site Selector Getting Started Guide

, Chapter 3, Setting Up

Your GSS.

Save your configuration changes to memory by entering the following
command:

gss3.example.com#

copy running-config startup-config

10.

Configure the GSS device as the standby GSSM in the GSS network and
direct it to the primary GSSM by entering the

gss enable gssm-standby

command.

The syntax for this command is as follows:

gss enable gssm-standby

primary_GSSM_hostname

primary_GSSM_IP_address

The argument are as follows:

–

primary_GSSM_hostname—

DNS hostname of the device currently

serving as the primary GSSM

Summary of Contents for GSS-4492R-K9







































































































































































































































Search results

Summary of Contents for GSS-4492R-K9

Reviews:

Related manuals for GSS-4492R-K9

Brands by name

Popular brands

Cisco GSS-4492R-K9, Administration Manual

Search results

Summary of Contents for GSS-4492R-K9

Reviews:

Related manuals for GSS-4492R-K9

Brands by name

Popular brands