Cisco Expressway CE1000 Appliance Installation Manual Download

Page: 4 / 16

The following components are field replaceable:

Hard disks

PSUs

1 Gb and 10 Gb SFP modules

To initiate a Return Material Authorization (RMA) go to

http://www.cisco.com/web/ordering/cs_

info/or3/o32/Return_a_Product/WebReturns/product_Online_web_returns.html

Related documents

Cisco Expressway Administrator Guide

- describes how to maintain and operate the Cisco Expressway

software.

Cisco Expressway Cluster Creation and Maintenance Deployment Guide

- describes how to create and

maintain a cluster of Cisco Expressways.

Training

Training is available online and at our training locations. For more information on all the training we provide
and where our training offices are located, visit

www.cisco.com/go/telepresencetraining

Glossary

A glossary of TelePresence terms is available at:

https://tp-tools-web01.cisco.com/start/glossary/

Cisco Expressway CE1000 Appliance Installation Guide (8.5)

Page 4 of 16

Introduction

Summary of Contents for Expressway CE1000 Appliance

















Search results

Summary of Contents for Expressway CE1000 Appliance

Reviews:

Related manuals for Expressway CE1000 Appliance

Brands by name

Popular brands

Cisco Expressway CE1000 Appliance, Installation Manual

Search results

Summary of Contents for Expressway CE1000 Appliance

Reviews:

Related manuals for Expressway CE1000 Appliance

Brands by name

Popular brands