Cisco BEKEM Manual Download Page 15 | Manualshive

Page: 15 / 16

background image

• Power over Ethernet (PoE) doesn't meet the required power-supply.

• Connected number of key expansion modules exceed maximum "Number of Units".

Solution

• Change the phone to use the same type of expansion module.

• Check the PoE the phone connected to.

• Check if the unit number is bigger than the “Number of Units".

Cisco IP Phone Key Expansion Module

15

Cisco IP Phone Key Expansion Module

Key Expansion Module Does Not Go Through the Normal Start Up Process

«
...
13
14
15
16
»

Summary of Contents for BEKEM

















Reviews:

No comments

Related manuals for BEKEM

Brand: cam Pages: 28

Brand: Feniex Pages: 6

Brand: Fencing SmartBox Pages: 11

Brand: Feiyu Pages: 4

Brand: FAZUA Pages: 84

Brand: GAI-Tronics Pages: 22

Brand: T-up Pages: 14

Brand: Oki Pages: 20

Brand: K&M Pages: 3

Brand: Panasonic Pages: 96

Brand: Panasonic Pages: 8

Brand: GE Pages: 60

Brand: Oki Pages: 20

Brand: Uniden Pages: 68

DECT Elite 9035+1

Brand: Uniden Pages: 68

Brand: Whispbar Pages: 15

Brand: GATmatic Pages: 13

HookUpz Smartphone Telescope Adapter

Brand: Carson Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands