Cisco BEKEM Manual Download Page 13

Page: 13 / 16

Allocate a Key Expansion Module Type

You can assign the type of key expansion module that the phone supports:

• BEKEM

• CP-8800-Audio

• CP-8800-Video

Before you begin

• Access the phone administration web page. See

Access the Phone Web Page

Procedure

Step 1

Select

Voice

Att Console

Step 2

Set the

KEM Type

field as described in the

General

table.

Step 3

Press

Submit All Changes

Allocate a Key Expansion Module Type with the Phone Menu

You can assign the type of key expansion module that the phone supports.

Procedure

Step 1

Press

Applications

Step 2

Select

User preferences

Attendant console preferences

KEM type

Step 3

Select the key expansion module type.

Step 4

Press

Save

Reset the Single LCD Screen Key Expansion Module

If you are having technical difficulties with your Cisco IP Phone 8800 Key Expansion Module, you can reset
the module to the factory default settings.

Cisco IP Phone Key Expansion Module

Allocate a Key Expansion Module Type

Summary of Contents for BEKEM

















Search results

Summary of Contents for BEKEM

Reviews:

Related manuals for BEKEM

Brands by name

Popular brands

Cisco BEKEM, Manual

Search results

Summary of Contents for BEKEM

Reviews:

Related manuals for BEKEM

Brands by name

Popular brands