Cisco Aironet 1530 Series, 1532 Installation Manual Download Page 69

Page: 69 / 69

2-37

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

OL-30864-01

Chapter 2 Installing the Access Point

Installing Antennas

Cisco Aironet 5-GHz 8-dBi Omnidirectional Antenna (AIR-ANT5180V-N)

The Cisco Aironet 5-GHz 8-dBi Omnidirectional Antenna is designed for outdoor use with Cisco
Aironet Outdoor Access Points with radios operating in the 5-GHz frequency band. This antenna has
8-dBi gain in the 5-GHz frequency band.

For detailed information on this antenna, refer to the document

Cisco Aironet 8-dBi Omnidirectional

Antenna (AIR-ANT5180V-N)

. Follow all safety precautions when installing the antennas, for information

on safety, refer to

“Safety Precautions when Installing Antennas” section on page 2-29

Figure 2-22

Cisco Aironet 5-GHz 8-dBi Omnidirectional Antenna - Installed Only on Model
AIR-CAP1532E-x-K9

Summary of Contents for Aironet 1530 Series, 1532






































































Search results

Summary of Contents for Aironet 1530 Series, 1532

Reviews:

Related manuals for Aironet 1530 Series, 1532

Brands by name

Popular brands

Cisco Aironet 1530 Series, 1532, Installation Manual

Search results

Summary of Contents for Aironet 1530 Series, 1532

Reviews:

Related manuals for Aironet 1530 Series, 1532

Brands by name

Popular brands