manualshive.com logo in svg

Cisco Aironet 1530 Series, 1532, Installation Manual

Share
Download
Cisco Aironet 1530 Series, 1532 Installation Manual Download Page 36

 

2-4

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

OL-30864-01

Chapter 2      Installing the Access Point

Safety Information

Warning

The cables specified in this installation guide that are used with the specified cable glands provide 
protection against ingress of moisture for a Type 4/IP67 classified enclosure. If substitute cable are 
used, the installer must ensure that the size (OD) of the cable meets the acceptable range allowed by 
the cable gland.

Warning

This equipment must be externally grounded using a customer-supplied ground wire before power is 
applied. Contact the appropriate electrical inspection authority or an electrician if you are uncertain 
that suitable grounding is available. 

Statement 366

Warning

Read the installation instructions before connecting the system to the power source. 

Statement 1004

Warning

Ultimate disposal of this product should be handled according to all national laws and regulations. 

Statement 1040

Safety Information

Follow the guidelines in this section to ensure proper operation and safe use of the access point.

FCC Safety Compliance Statement

The FCC, with its action in ET Docket 96-8, has adopted a safety standard for human exposure to RF 
electromagnetic energy emitted by FCC-certified equipment. When used with approved Cisco Aironet 
antennas, Cisco Aironet products meet the uncontrolled environmental limits found in OET-65 and ANSI 
C95.1, 1991. Proper operation of this radio device according to the instructions in this publication results 
in user exposure substantially below the FCC recommended limits.

Safety Precautions

Warning

In order to comply with radio frequency (RF) exposure limits, the antennas should be placed no less 
than 20 cm (8”) from your body or nearby persons. 

Statement 339

Warning

Do not work on the system or connect or disconnect cables during periods of lightning activity. 

Statement 1001

Warning

A readily accessible two-poled disconnect device must be incorporated in the fixed wiring. 

Statement 1022

Summary of Contents for Aironet 1530 Series, 1532






































































Reviews:

No comments

Brands by name

Popular brands

Load more brands