Cisco AIR-CAP3702E-A-K9 Getting Started Manual Download

Page: 41 / 44

Access Point Specifications

Table 2

lists the technical specifications for 3700 series access points.

Table 2

Access Point Specifications

Category

Specification

Dimensions (LxWxD)

8.68 x 8.68 x 1.84 in. (22.04 x 22.04 x 4.67 cm)

Weight

1.9 lbs (0.86 kg)

Operating temperatures AP3702E: -4 to 131 degrees F (-20 to 55 degrees C)

AP3702I: 32 to 104 degrees F (0 to 40 degrees C)

Storage temperature

–22 to 185 degrees F (–30 to 85 degrees C)

Humidity

10% to 90% (noncondensing)

Antennas

AP3702I: Integrated; AP3702E: External

Compliance

The 3700 series access point complies with UL 2043 for products installed
in a building’s environmental air handling spaces, such as above suspended
ceilings.

Safety

UL 60950-1
CAN/CSA C22.2 No. 60950-1
IEC 60950-1 with all national deviations
EN 60950-1
UL 2043

EMI and Susceptibility

FCC Part 15.107 and 15.109 Class B
ICES-003 Class B (Canada)
EN 301.489
EN 55022 Class B
EN 55024
VCCI Class B

Radio

FCC Part 15.247, 15.407
Canada RSS-210
Japan Telec 33, 66, T71
EN 330.328, EN 301.893
FCC Bulletin OET-65C
Industry Canada RSS-102

Maximum power and
channel settings

Maximum power and the channels allowed in your regulatory domain,
refer to

Channels and Maximum Power Settings for Cisco Aironet

Lightweight Access Points

. This document is available on Cisco.com.

Summary of Contents for AIR-CAP3702E-A-K9













































Search results

Summary of Contents for AIR-CAP3702E-A-K9

Reviews:

Related manuals for AIR-CAP3702E-A-K9

Brands by name

Popular brands

Cisco AIR-CAP3702E-A-K9, Getting Started Manual

Search results

Summary of Contents for AIR-CAP3702E-A-K9

Reviews:

Related manuals for AIR-CAP3702E-A-K9

Brands by name

Popular brands