Cisco AIR-CAP3702E-A-K9 Getting Started Manual Download | Manualshive

Page: 17 / 44

background image

17

Step 3

Peel off the label from the back of the 3700 series access point to reveal the module port
connector.

Step 4

Align the module’s connector with the connector on the back of the access point and click the
module into place.

1

Openings for module’s antennas.

2

Label covering port connector.

345379

1

2

1

«
...
15
16
17
18
19
...
»

Summary of Contents for AIR-CAP3702E-A-K9













































Reviews:

No comments

Related manuals for AIR-CAP3702E-A-K9

Brand: Planet Pages: 37

BLUESOCKET 1930

Brand: ADTRAN Pages: 4

Brand: Comet Labs Pages: 46

Brand: Bosslan Pages: 4

Brand: EnGenius Pages: 2

Brand: EnGenius Pages: 4

Brand: HomeMatic Pages: 23

Brand: HomeMatic Pages: 45

Brand: Kaon Pages: 17

Brand: 4IPNET Pages: 26

Brand: U4EA Pages: 16

Brand: Ebyte Pages: 27

Brand: AAxeon Pages: 50

Brand: Cambium Networks Pages: 2

Brand: H3C Pages: 15

Brand: 3Com Pages: 8

Brand: Ublox Pages: 66

Brand: Sitecom Pages: 86

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands