Cisco 7821 Administration Manual Download

Page: 22 / 360

Updated Section

Revision

Configure Star Codes for DND, on page 134

Added star code support on Do Not Disturb feature

•

Programmable Softkeys, on page 174

Updated programmable softkeys changes

Configure Provisioning Authority, on page 178

Updated provisoning authority changes

Enable Do Not Disturb, on page 133

Updated Do Not Disturb feature changes

•

Configure a Phone to Accept Pages
Automatically, on page 182

Added Automatic paging feature

#unique_125

Updated all sections of Phone Configuration Utility
(Web page)

New Information for Firmware Release 10.4(1) SR1

All new features have been added to

Telephony Features for Cisco IP Phone, on page 151

Updated Section

Revision

Configure a Paging Group (Multicast Paging), on page
167

Added Configure a Paging Group

Configure Alphanumeric Dialing, on page 166

Added Configure Alphanumeric Dialing

New Information for Firmware Release 10.4(1)

All new features have been added to

Telephony Features for Cisco IP Phone, on page 151

Updated Section

Revision

Configure a Speed Dial on a Line Key, on page 159

Added Speed-Dial on a line key

Configure Provisioning Authority, on page 178

Added Provisioning Authority

Configuring Programmable Softkeys, on page 171

Added Customization of Programmable Softkey

Telephony Features for Cisco IP Phone, on page 151

Added Remote Customization

Voice Quality Reporting, on page 323

Added Voice Quality Reporting using SIP Publish

Download Problem Reporting Tool Logs, on page 180

Added Problem Report Tool

Cisco IP Phone 7800 Series Multiplatform Phones Administration Guide

New and Changed Information

New Information for Firmware Release 10.4(1) SR1

Summary of Contents for 7821









































































































































































































































































































































































Search results

Summary of Contents for 7821

Reviews:

Related manuals for 7821

Brands by name

Popular brands

Cisco 7821, Administration Manual

Search results

Summary of Contents for 7821

Reviews:

Related manuals for 7821

Brands by name

Popular brands