manualshive.com logo in svg

Cisco 2100 Series, Configuration Manual

The Philips 2100 Series user manual is your essential guide to operating and maximizing the potential of your device. With a simple and intuitive layout, this manual provides step-by-step instructions and troubleshooting tips. Download it for free at manualshive.com and unlock the full potential of your Philips 2100 Series.

Share
Download
background image

 

3-10

Cisco Wireless LAN Controller Configuration Guide

OL-17037-01

Chapter 3      Configuring Ports and Interfaces

Configuring the Management, AP-Manager, Virtual, and Service-Port Interfaces

Note

A zero value for the VLAN identifier (on the Controller > Interfaces page) means that the interface is 
untagged.

The default (untagged) native VLAN on Cisco switches is VLAN 1. When controller interfaces are 
configured as tagged (meaning that the VLAN identifier is set to a non-zero value), the VLAN must be 
allowed on the 802.1Q trunk configuration on the neighbor switch and not be the native untagged VLAN. 

Cisco recommends that tagged VLANs be used on the controller. You should also allow only relevant 
VLANs on the neighbor switch’s 802.1Q trunk connections to controller ports. All other VLANs should 
be disallowed or pruned in the switch port trunk configuration. This practice is extremely important for 
optimal performance of the controller.

Note

Cisco recommends that you assign one set of VLANs for WLANs and a different set of VLANs for 
management interfaces to ensure that controllers properly route VLAN traffic.

Follow the instructions on the pages indicated to configure your controller’s interfaces and ports:

•

Configuring the Management, AP-Manager, Virtual, and Service-Port Interfaces, page 3-10

•

Configuring Dynamic Interfaces, page 3-16

•

Configuring Ports, page 3-19

•

Enabling Link Aggregation, page 3-29

•

Configuring a 4400 Series Controller to Support More Than 48 Access Points, page 3-34

Configuring the Management, AP-Manager, Virtual, and 
Service-Port Interfaces

Typically, you define the management, AP-manager, virtual, and service-port interface parameters using 
the Startup Wizard. However, you can display and configure interface parameters through either the GUI 
or CLI after the controller is running.

Note

When assigning a WLAN to a DHCP server, both should be on the same subnet. Otherwise, you need to 
use a router to route traffic between the WLAN and the DHCP server.

Summary of Contents for 2100 Series





























































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2100 Series

Watchguard XCS 880 Hardware Manual preview
XCS 880
Brand: Watchguard Pages: 20
PaloAlto Networks PA-5200 Seriesp Hardware Reference Manual preview
PA-5200 Seriesp
Brand: PaloAlto Networks Pages: 60
Lanner FW-8894 User Manual preview
FW-8894
Brand: Lanner Pages: 89
Barracuda CloudGen F80 Manual preview
CloudGen F80
Brand: Barracuda Pages: 6
Watchguard Firebox T80 Quick Start Manual preview
Firebox T80
Brand: Watchguard Pages: 2
Watchguard QMS 1000 Quick Start Manual preview
QMS 1000
Brand: Watchguard Pages: 8
Watchguard CL58AE32 Quick Start Manual preview
CL58AE32
Brand: Watchguard Pages: 2
Watchguard Firebox 2500 Series Hardware Manual preview
Firebox 2500 Series
Brand: Watchguard Pages: 30
Watchguard Firebox T40 Hardware Manual preview
Firebox T40
Brand: Watchguard Pages: 18
Watchguard DS1AE3 Quick Start Manual preview
DS1AE3
Brand: Watchguard Pages: 37
Watchguard Firebox T55 Quick Start Manual preview
Firebox T55
Brand: Watchguard Pages: 29
Watchguard Firebox Vclass V100 Administration Manual preview
Firebox Vclass V100
Brand: Watchguard Pages: 38
Watchguard BF4S16E5W User Manual preview
BF4S16E5W
Brand: Watchguard Pages: 208
SonicWALL TZ 100 Series Quick Start Manual preview
TZ 100 Series
Brand: SonicWALL Pages: 6
SonicWALL NSA 2650 Installation Manual preview
NSA 2650
Brand: SonicWALL Pages: 2
ZyXEL Communications ZyWALL 70 User Manual preview
ZyWALL 70
Brand: ZyXEL Communications Pages: 705
ZyXEL Communications ATP200 User Manual preview
ATP200
Brand: ZyXEL Communications Pages: 852
Untangle u500 Setup Manual preview
u500
Brand: Untangle Pages: 2

Brands by name

Popular brands

Load more brands