background image

 

Corporate Headquarters:

Copyright © 2003 Cisco Systems, Inc. All rights reserved.

Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

Cisco 1751 Voice-over-IP Quick Start Guide

The Cisco 1751 Voice over IP Quick Start Guide explains how to install WAN Interface Cards and Voice 
Interface Cards, how to run configuration tools, and how to perform essential Voice-over-IP (VoIP) 
configuration tasks.

This document contains the following sections:

Audience, page 1

Conventions, page 2

Installing WAN and Voice Interface Cards, page 2

Cisco Router and Security Device Manager, page 9

Configuring Voice-over-IP, page 10

List of Terms, page 30

Obtaining Documentation, page 31

Documentation Feedback, page 32

Obtaining Technical Assistance, page 32

Obtaining Additional Publications and Information, page 33

Audience

This guide is intended primarily for users who configure and maintain routers, but are not necessarily 
familiar with tasks, the relationship between tasks, or the commands necessary to perform particular 
tasks to configure VoIP. We assume that you are familiar with Cisco IOS software, IP and telephony 
networks, and PBX operation for E&M installations. 

List of Terms provides definitions for many of the technical terms used in this document.

Summary of Contents for 1751



































Reviews: