background image

 

 

900-525-31-00 

6

 

Item Specification 

Remarks 

1/38sec Progressive Scan (Normal Operation) 

 

Horizontal frequency        40.22 KHz 

1790 CLK 

Vertical frequency          37.66 Hz 

1068 HD 

Scanning system 

Non-Interlaced 

Pixel clock                                  72 MHz 

 

Partial Scan 

                          V Scanning          Rate            Effective V line 

OFF  Progressive 1068 lines    38 fps     1024 lines 
Partial Scan              550 lines        73 fps            258 lines 
(min 548 line:73 fps: 255 line

max 832 line:48 fps: 681 line) 

Refer to 

7.1.3 for the 
details 

Sensitivity F2.8

   

    400 lx        (at 1/38 sec exposure, Gain 0dB) 

 

Min. illumination 

F1.4      0.5 lx (at 1/38 sec exposure, Gain 12dB, VS 50 IRE) 

 

 

5.2.    Camera Output Signal Specification 

Item Specification 

Remarks 

Horizontal resolution 

  1024 TV lines 

 

(1) LVAL output 

Polarity Negative 

(2) FVAL output 

Polarity Negative 

(3) DVAL output 

BLK output (effective pixel area), Positive 

Camera Link 
connector 

(1) HD/VD Input 

Polarity Negative (at External Sync mode) 
Input level shall be 2

5Vp-p with connected 

to the camera.    HD/VD signals shall not 
include noises such as chattering. 

(2) HD/VD Output 

Polarity Negative (at Internal Sync mode) 

(3) WEN Output 

Single VD/FVAL/Exposure selectable (at 

External sync mode) 

Sync. 
Signal I/O 

  Please refer to 7.4.    12 pin Circular Connector HD/VD trigger 

I/O circuit. 

12pin Circular 
connector 

   

(Refer to   
Address 55) 

Polarity POSI/NEGA

 

Selectable Refer 

to 

 

Address 011 

Input level shall be 2

5Vp-p with connected 

to the camera.   Trigger input shall not include 
noises such as chattering. 

12 pin circular 

connector 

 

Input signal level 

CC1 Input 

Camera Link 
connector 
 

Trigger 
input 

  Min. Trigger Pulse 

width  

Over 1 HD 

 

Summary of Contents for VCC-G32S21CL































Reviews: