CIS VCC-2CXP6R Product Specification & Operational Manual Download Page 14

Page: 14 / 33

VCC-2CXP6R

Rev.905-0187-02



TriggerMode

: Trigger mode



: Validate the trigger selected by TriggerSource. (TriggerSelector = FrameStart)



Off

: Invalidate the trigger selected by TriggerSource. (TriggerSelector = AcquisitionStart)

※ Please do not change TriggerMode while grabbing (acquiring image).



TriggerSyncMode : Trigger sync. mode



LineSync

: H sync. trigger mode (Exposure time is controllable per line)

Fixed/Pulse width trigger shutter mode

Overlapping operation (Exposure while reading out image) is valid.



ClockSync

: CLK sync. trigger mode (Exposure time is controllable per sensor clock)

FAST fixed/FAST pulse width trigger shutter mode

Overlapping operation (Exposure while reading out image) is invalid.

※ Please change TriggerSyncMode while there is no trigger input.
※ Please set Free run mode (internal sync. mode) after set itself to LineSync mode.



TriggerSelector : Trigger selector

This is to select how to start capturing the image and to select the polarity out of following.



AcquisitionStart

: Free run mode [Internal sync. mode]



FrameStart

: External trigger mode

※

Please do not change TriggerSelector while grabbing (acquiring image).



TriggerActivation

: Trigger activation

This is to select how to start capturing the image and to select the polarity out of following.



RisingEdge

: Fixed trigger shutter mode: Rising edge (Timed)



FallingEdge

: Fixed trigger shutter mode: Falling edge (Timed)



LevelHigh

: Pulse width trigger shutter mode: High active (TriggerWidth)



LevelLow

: Pulse width trigger shutter mode: Low active (TriggerWidth)



TriggerSource

: Trigger source

This is to select where to input the external trigger.



Software

: TriggerSoftware



LinkTrigger0 : External trigger input from CoaXPress Host Device

Please refer to the product specifications & operational manual of the Host Device
(ex. grabber board) to use for how to generate the trigger.



Line0

: Input the external trigger via 6pins circular connector.



TriggerSoftware

: Software trigger

A trigger is generated in the camera and capture images for 1 frame when this command is
executed. Please make sure to set TriggerSource to Software.

※ Software Trigger is valid at Rising Edge.

Summary of Contents for VCC-2CXP6R
































Search results

Summary of Contents for VCC-2CXP6R

Reviews:

Related manuals for VCC-2CXP6R

Brands by name

Popular brands

CIS VCC-2CXP6R, Product Specification & Operational Manual

Search results

Summary of Contents for VCC-2CXP6R

Reviews:

Related manuals for VCC-2CXP6R

Brands by name

Popular brands