background image

VCC-2CXP6M 

                                                                                                                           

Rev.905-0186-02 

©2019 CIS Corporation. All rights reserved. 

26 

 

5.22.

 

Test Pattern Indication 

 

Test pattern can be output from the camera. It is useful to check if your system is operating properly. 

ImageFormatControl 

TestPattern 

Off 
GrayHorizontalRamp 

 

This function cannot be set when cursor indication is ON. 

 

5.23.

 

Cursor Indication 

 

This is to indicate the cursor on the screen. 

ImageFormatControl 
CursorPattern 

Off/On 

CursorOffsetX 

X coordinate 

CursorOffsetY 

Y coordinate 

CursorColor 

White/Black 

 

 

This function cannot be set when test pattern indication is ON. 

 

CursorPattern:              Specify if the cursor shall be indicated or not. 

 

CursorOffsetX:              This is to specify the X coordinate of vertical cursor. 

 

CursorOffsetY:              This is to specify the Y coordinate of horizontal cursor. 

 

CursorColor:                  This is to specify the color of the cursor. (White/Black)

 

 

 
5.24.

 

LED Operational Mode 

 

When it is ON, lighting patterns of LED shows the camera status by the way of its lighting. 

DeviceControl 

DeviceIndicatorMode 

Active 
ErrorStatus 
Inactive 

 

Active

     

  

: This is to indicate the communication status of CoaXPress. 

 

ErrorStatus

 

  : Lights OFF at normal status. Lights only when there was a system error. 

 

Inactive

     

 

: ALL LED OFF. 

 
5.25.

 

Camera Timing Output 

□ 

The signals below can be output from 3pin of 6pins circular connecter by LineSource settings. 

 

Digital IO Control 
LineSelector 

Line0 

LineMode 

Output 

LineSource 

OFF 
ExposureActive 
FrameActive 
LineActive 
TriggerPacketActive 

      ・

LineSource

 

ExposureActive 

: This is to indicate exposure period of image sensor by Hi Active. 

FrameActive 

: This is to indicate effective period of frame by Hi Active. 

LineActive 

: This is to indicate effective period of line by Hi Active. 

TriggerPacketActive 

: This is to output uplink trigger packet signal from frame grabber by decoding. 

         

Summary of Contents for VCC-2CXP6M



































Reviews: