background image

VCC-2CXP6M 

                                                                                                                           

Rev.905-0186-02 

©2019 CIS Corporation. All rights reserved. 

12 

 

5.6.

 

Trigger Sync. Mode and Delay Time to Start Exposure 

H sync. trigger mode (LineSync): 1H of jitter may occur from inputting trigger to exposure.   

(Overlapping operation is valid.) 

CLK sync. trigger mode (ClockSync): Less delay time from trigger input, and the precise trigger operation is valid.   

(Overlapping operation is invalid.) 

 

Trigger sync. mode and delay time to start exposure 

 

CXP6_X1 

CXP3_X1 

Exposure delay to start exposure at H sync. trigger (LineSync) 

Approx. 4H~5H 

Approx. 4H~5H 

Exposure delay to start exposure at CLK sync. trigger (ClockSync) 

Approx. 0.13us 

Approx. 0.13us 

 

5.7.

 

Restrictions on Trigger Pulse Input Timing 

 

The next trigger pulse can be input while reading out signals (Readout). However, please do not input a trigger 

pulse which ends its exposure while reading out the prior signals. In other words, a trigger pulse, while reading 

out signals for the prior frame and starts reading out signals for the next frame, cannot be input. 

Exposure Out

TRIG IN

Readout 

(FVAL Out)

(Video Out)

Effective Line

(A)

 

 

When a trigger is input with the restricted timing explained the above, “IllegalTriggerFlag” becomes “1”. 

 

Acquisition Control

 

 

IllegalTriggerFlag 

0 or 1 

                         

※Since overlapping operation is invalid at CLK sync. mode, the trigger at this timing shall be masked and   

“IllegalTriggerFlag” will not become “1”. 

 

Device Control 
ErrorFlagReset 

Execute 

                       

This is to reset IllegalTriggerFlag to “0”. 

 
 
 
 
 

Summary of Contents for VCC-2CXP6M



































Reviews: