Cirrus Logic CS8952 Page 55 Manual Download | Manualshive

Page: 55 / 82

background image

CS8952

CrystalLAN™ 100BASE-X and 10BASE-T Transceiver

55

3

Rx Disable

Read/Write 0

When set, the receiver is disabled and no incoming
packets pass through the receiver. The link will
remain established and, if operating at 100 Mb/s, the
descrambler will remain locked. When clear, the
receiver is enabled.

If Rx Disable is set while a packet is being received,
reception is completed and no subsequent receive
packets are allowed until Rx Disable is cleared again.
Also, if Rx Disable is cleared while a packet is being
received, the receiver will remain disabled until the
end of the incoming packet. This prevents fragments
from being sent to the MAC.

Note: This bit is disabled, and writes to this bit are
ignored when the National Compatibility Mode bit of
the 10BASE-T Configuration Register (address 1Ch)
is set.

2

LED1 Mode

Read/Write 0

This bit defines the mode of Pin LED1. When this bit
is set, pin LED1 indicates Carrier Integrity Monitor
status as determined by the CIM Status bit in the Self
Status Register (address 19h). When this bit is clear,
LED1 indicates 10 Mb/s or 100 Mb/s transmission
activity.

1

LED4 Mode

Read/Write 0

This bit defines the mode of Pin LED4. When this bit
is set, pin LED4 indicates full duplex mode for
10 Mb/s or 100 Mb/s. When this bit is clear, LED4
indicates Polarity in 10 Mb/s mode or full-duplex in
100 Mb/s mode.

0

Digital Reset

Read/Write 0

When set, this bit will reset all digital logic and regis-
ters to their initial values. The analog circuitry will not
be affected.

Note: This bit is disabled, and writes to this bit are
ignored when the National Compatibility Mode bit of
the 10BASE-T Configuration Register (address 1Ch)
is set.

BIT

NAME

TYPE

RESET

DESCRIPTION

«
...
53
54
55
56
57
...
»

Summary of Contents for CS8952



















































































Reviews:

No comments

Related manuals for CS8952

Brand: Barlow Wadley Pages: 13

Brand: Eaton Pages: 2

Brand: Kathrein Pages: 44

Brand: Magnetrol Pages: 16

Brand: Magnetrol Pages: 108

Brand: Magnetrol Pages: 35

Brand: Magnetek Pages: 25

Brand: SpeakerCraft Pages: 36

Brand: AOR Pages: 95

THERMASGARD ALTM 2-VA

Brand: S+S Regeltechnik Pages: 16

Brand: Grundig Pages: 25

Freeview TRF-7150

Brand: Topfield Pages: 78

Brand: Icom Pages: 7

Satlook Micro G2

Brand: emitor Pages: 24

Brand: tbs electronics Pages: 15

Brand: DAAB Pages: 8

Brand: EZCast Pro Pages: 33

Brand: Icom Pages: 101

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands