background image

CRD5378

36

DS639RD2

3.3.3

Analog Front End

The 

Analog Front End

 sub-panel configures the amplifier, modulator, and test DAC pin options. Pin op-

tions are controlled through the GPIO outputs of the digital filter.

Any changes made under this sub-panel will not be applied to the target board until the 

Configure

 button

is pushed. The 

Configure

 button writes the new configuration to the target board and then enables the

data 

Capture

 button.

3.3.4

Test Bit Stream

The 

Test Bit Stream

 sub-panel configures test bit stream (TBS) generator parameters. The digital filter

data sheet describes TBS operation and options.

The 

DAC Quick Set

 controls automatically set the 

Interpolation

Clock Rate

, and 

Gain Factor

 controls

based on the selected 

Mode

Freq

, and 

Gain

. Additional configurations can be programmed by writing the

Interpolation

Clock Rate

, and 

Gain Factor

 controls manually.

Any changes made under this sub-panel will not be applied to the target board until the 

Configure

 button

is pushed. The 

Configure

 button writes the new configuration to the target board and then enables the

data 

Capture

 button.

Control

Description

Amp Mux

Selects the input source for the CS3301A/02A amplifiers.  An internal termination, 
external INA inputs or external INB inputs can be selected.

DAC Mode

Selects the operational mode of the CS5373A test DAC. The test DAC operational 
modes are AC dual output (OUT&BUF), AC precision output (OUT only), AC buffered 
output (BUF only), DC common mode output (DC Common), DC differential output 
(DC Diff), or AC common mode output (AC Common). The test DAC can also be 
powered down (PWDN) when not in use to save power.

Gain

Sets the amplifier gain range and test DAC attenuation.  Amplifier gain and DAC 
attenuation settings of 1x, 2x, 4x, 8x, 16x, 32x, or 64x can be selected and are con-
trolled together.

Sw

Selects how the DAC_BUF to INA analog switches are enabled when connected to 
the CRD5376. This control is not applicable to the CRD5378 and is disabled.

Control

Description

DAC Quick Set

Automatically sets test bit stream options. 

Mode

 selects sine or impulse output mode, 

Freq

 selects the test signal frequency for sine mode, and 

Gain

 selects the test signal 

amplitude in dB.

Interpolation

Manual control for the data interpolation factor of the test bit stream generator.

Clock Rate

Manual control for the output clock and data rate of the test bit stream generator.

Gain Factor

Manual control to set the test bit stream signal amplitude.

Sync

Enables test bit stream synchronization by the MSYNC signal.

Loopback

Enables digital loopback from the test bit stream generator output to the digital filter 
input.

Summary of Contents for CRD5378

































































Reviews: