Quick Start Guide, 61700630E1-13D, February 2014
1
4
Copyright © 2014 ADTRAN, Inc. All Rights Reserved.
N
ET
V
ANTA
4430 R
OUTER
P/N 1700630E1
G
ETTING
S
TARTED
Two configuration methods are available for your NetVanta router:
•
Web-based graphical user interface (GUI)
•
ADTRAN Operating System (AOS) command line interface (CLI)
The GUI lets you configure the main unit settings and provides online guidance and explanations
for each setting, and configuration wizards to help you get started. However, using the AOS CLI
may be necessary for more advanced configurations.
A
CCESS
THE
GUI
You may access the GUI from any web browser on your network by following these steps:
1.
Connect the router to your PC using the
ETH 0/1
port on the front of the unit and an Ethernet
cross-over cable.
2.
Set your PC to a fixed IP address of
10.10.10.2
. To change your PC IP address, navigate to
Computer
>
Control Panel
>
Network Connections
>
Local Area Connection
>
Properties
>
IP (TCP/IP)
and select
Use this IP Address
. Enter these parameters:
IP Address:
10.10.10.2
Subnet Mask:
255.255.255.0
Default Gateway:
10.10.10.1
You do not need to enter any domain naming server (DNS) server information. After the
information is entered, select
Ok
twice, and close the Network Connections dialog box.
If
you cannot change the PC’s IP address, you will need to change the unit’s IP address using
the CLI. (Refer to the next two sections for instructions.)
3.
Open a web browser and enter the unit’s IP address in your browser address line as follows:
http://10.10.10.1
. The default IP address is
10.10.10.1
, but if you had to change the unit’s IP
address using the CLI, enter that address in the browser line.
4.
You will then be prompted for the user name and password (the default settings are
admin
and
password
).
5.
The initial GUI screen appears. You can access initial setup information by selecting
Setup
Wizard
from the menu on the left.
A
CCESS
THE
CLI
Access the AOS CLI via the
CONSOLE
port, a Telnet session, or from the GUI. To establish a
connection to the NetVanta router
CONSOLE
port, you need the following items:
•
PC with VT100 terminal emulation software
•
Straight-through serial cable with a DB-9 (male) connector on one end and the appropriate
interface for your terminal or PC communication port on the other end
There are many terminal emulation applications available on the web. PuTTY,
SecureCRT, and HyperTerminal are a few examples.
C
ONFIGURE
Y
OUR
A
PPLICATION
The applications you will need to configure vary by product and by network. Review the list of
defaults for your unit before deciding what applications to configure. The following are some
common applications that should be configured on startup. These are all available on
ADTRAN’s
Support Forum.
R
ESTORING
F
ACTORY
D
EFAULTS
On units that have a console port, you cannot restore the factory defaults, but must rather erase
the device’s configuration and then reconfigure the unit to operate correctly for your network. To
erase the unit’s current configuration, follow these steps:
1.
Access the unit’s CLI and enter
enable
at the
>
prompt.
2.
Enter
erase startup-config
at the
#
prompt. The device will have a blank configuration upon
reboot.
3.
Enter
reload
at the
#
prompt to begin restarting the device. When prompted to save
configuration, enter
no
. When prompted to reboot, enter
yes
.
4.
Upon reboot, you will have to reconfigure the unit using the
CONSOLE
port. Follow the
steps outlined here or in the technical note,
Accessing the Web Interface in AOS
at
https://supportforums.adtran.com
.
Configuring T1 Access to a Remote Site
Using PPP in AOS
Configuring Internet Access (Many to One NAT) with
the Firewall Wizard in AOS
Configuring Port Forwarding in AOS
Configuring QoS for VoIP in AOS
Configuring PPP in AOS
Configuring HDLC in AOS
Configuring Frame Relay in AOS
Configuring QoS in AOS
Configuring DHCP Server in AOS
Configuring a VPN Using Main Mode in AOS
Configuring a VPN Using Aggressive Mode
in AOS
Important:
For additional details on product features, specifications,
installation, and safety, refer to
NetVanta 4000 Series Hardware Installation
Guide
at
https://supportforums.adtran.com.
.
N
ET
V
ANTA
4000 S
ERIES
D
EFAULTS
Feature
Default Value
IP Address
10.10.10.1
Username
admin
Password
password
HTTP Server
Enabled
Event History
On
IP Routing
Enabled
