background image

Copyright 

©

 Cirrus Logic, Inc. 2007

(All Rights Reserved)

http://www.cirrus.com

Evaluation Board for CS43L22

Features



Analog Passthrough Input

– Four Stereo Line Input Jacks
– Channel Mixer



Analog Output

– Stereo Headphone Jack w/ HP Detect 

Capability

– Speaker Output via Differential Stereo 

PWM Terminals and Audio Jacks



8- to 96-kHz S/PDIF Interface

– Optical and RCA S/PDIF Input Jacks
– CS8416 Digital Audio Receiver



I/O Stake Headers

– External Control Port Accessibility
– External DSP Serial Audio I/O Accessibility



Multiple Power Supply options via Battery or 

External Power Supplies.



1.8 V to 3.3 V Logic Interface



FlexGUI S/W Control - Windows

®

 Compatible

– Pre-Defined & User-Configurable Scripts

Description

Using the CDB43L22 evaluation board is an ideal way
to evaluate the CS43L22. Use of the board requires an
analog/digital signal source, an analyzer and power
supplies. A Windows

 

PC-compatible computer is also

required in order to configure the CDB43L22.

System timing can be provided by the CS8416, by the
CS43L22 with supplied master clock, or via an I/O stake
header with a DSP connected. 1/8th inch audio jacks
are provided for the analog passthrough inputs and
HP/Line outputs. Two pairs of banana jacks and an ad-
ditional pair of 1/8th inch audio jacks are provided to
monitor the stereo differential speaker PWM output
from the CS43L22. Digital input connections are via
RCA phono or optical connectors to the CS8416
(S/PDIF Rx).

The Windows-based software GUI provided makes
configuring the CDB43L22 easy. The software commu-
nicates through the PC’s USB port to configure the
board and FPGA registers so that all features of the
CS43L22 can be evaluated. The evaluation board may
also be configured to accept external timing and data
signals for operation in a user application during system
development.

ORDERING INFORMATION

CDB43L22

Evaluation Board

USB 

µ controller 

CS43L22

S/PDIF Input 

(CS8416)

PSIA Input 

Header

FPGA

Oscillator 

(socket)

I

2

C Interface

Reset

Reset

PLL

Clk/Data 

SRC

(CS8421)

Analog Output

(Line + Headphone)

Speaker 
Outputs

Analog 

Passthrough

Input

External System 

Input Header

OCTOBER '07

DS792DB1

CDB43L22

Summary of Contents for CDB43L22

































Reviews: