Cirronet HopNet HN-210X User Manual Download Page 60

Page: 60 / 64

HopNet RS-232 Serial ModBus Radio

Technical Specifications

Refer to the tables below for the technical specifications for the HopNet radio
Remotes.

Electrical

Specification Value

Transmitter FCC ID

HSW-2410M

Transmit Power

EIRP: +24 dBm Nominal (HN-21xD); +14dBm EU
mode; +18 dBm (HN-21xDX); +8dBm EU mode

Hopping Patterns

User configurable, 64 patterns (networks) available

Number of Channels

75 US; 25 France

Line-of-Sight Range

Greater than 3.5 miles (up to 20 miles with HN-
21xDX and appropriate antennas)

Frequency Band

2401-2475 MHz (USA)
2448-2478 MHz (France)
2448-2473 MHz (Spain)
2473-2495 MHz (Japan)
2452-2478 MHz ( Canada)

Approvals

US FCC: Part 15. 203
Industry Canada
European Community: CE Marked

Receiver Sensitivity

-93 dBm (HopNet integrated patch antenna adds 6 dB
to the link budget and -99dBm sensitivity)

Data Interface

RS-232

Input Power at Connector 9 - 30 VDC Operating

160 mA Typical (750 mA surge)

2000- 2004 Cirronet

™

Inc

M-2410-0022 Rev B

Summary of Contents for HopNet HN-210X

































































Search results

Summary of Contents for HopNet HN-210X

Reviews:

Brands by name

Popular brands

Cirronet HopNet HN-210X, User Manual

Search results

Summary of Contents for HopNet HN-210X

Reviews:

Brands by name

Popular brands