manualshive.com logo in svg

Circutor RGU-10, Instruction Manual, Page: 8 / 46

Share
Download
Circutor RGU-10 Instruction Manual Download Page 8

8

RGU-10, RGU-10C

Instruction Manual

 3�- INSTALLING THE DEVICE

       

 3.1.- PRELIMINARY RECOMMENDATIONS

The operators using and handling the device must follow the safety measures 

established in the country where the device will be used to guarantee its safe 

operation, using personal protective equipment if needed. 

The 

RGU-10

 device must be installed by authorised and qualified staff.

Disconnect the device from the mains and disconnect the measuring devices before handling, 

changing the connections of or replacing the device. Handling the device while it is connected 

is hazardous to people nearby.

The cables must be in perfect working order to prevent accidents or injuries to people and/or 

damage to the facilities/installations.

Limit the operation of the device to measuring the specified current or voltage values.

The manufacturer of the device shall not be held responsible for any damage resulting from the 

user or installation company failing to observe the warnings and/or recommendations indicated 

in this manual nor for any damage resulting from the use of non-original products or accesso-

ries or those from other brands.

Do not use the device to take measurements if you detect an anomaly or malfunction.

Check the environment in which the device is installed before taking a measurement. Do not 

use the device to take measurements in dangerous, explosive, wet or damp environments.

Disconnect the device from the mains and from the power supply (both the device 

and its measuring system) before performing any maintenance work, repairs or 

handling any of the connections of the device. 

Contact the after-sales service if you detect that the device is not working prop-

erly.

 

Summary of Contents for RGU-10















































Reviews:

No comments