background image

 

2

READ ENTIRE PAGE BEFORE PROCEEDING 

 
FOR SAFETY OF PERSONNEL AND TO PREVENT DAMAGE TO EQUIPMENT, THE FOLLOWING 
NOMENCLATURE HAS BEEN USED IN THIS MANUAL: 
 

 

DANGER

 

 

Failure to observe precautions noted in this box can result in severe bodily injury or loss 
of life. 

 

 

WARNING

 

 

Failure to observe precautions noted in this box can cause injury to personnel by 
accidental contact with equipment or liquids.  Protection should be provided by user to 
prevent accidental contact. 

 

 

CAUTION

 

 

ATTENTION

 

 

Failure to observe precautions noted in this box can cause damage or failure of 
equipment. 

 

Non compliance of safety 
instructions identified by 
the following symbol could 
affect safety for persons: 

Safety instructions where 
electrical safety is 
involved are identified by:

Safety instructions which 
shall be considered for 
reasons of safe operation of 
the pump and/or protection 
of the pump itself are 
marked by the sign: 

 

 

ATTENTION 

 

CONTENTS 

 

Safety and Table of Contents .................................................................................................  2 
General Instructions ................................................................................................................ 3 
Introduction and Description .................................................................................................... 3 
Pump Model Identification ....................................................................................................... 3 
Ordering Instructions ............................................................................................................... 4 
Operation … ............................................................................................................................ 4 
Parts List … ............................................................................................................................. 5 
Maintenance, Bearing & Seal Installation ................................................................................ 6 
Disassembly and Assembly Instructions ................................................................................. 6 
Trouble shooting ...................................................................................................................... 9 

Field and Factory Service and Parts

 ............................................................................................. 9 

Pump Assembly Drawings ............................................................................................... 10-18 

 
 

 

ATTENTION

 

If operation of this pump is critical to your business, we strongly recommend 
you keep a spare pump or major repair kit in stock at all times.  As a minimum, 
a minor repair kit (o-rings, gaskets, shaft seal and bearings) should be kept in 
stock so pump refurbishment after internal inspection can be accomplished. 

 

Summary of Contents for IMO 143




















Reviews: