background image

Step 2. 

The water level of the inground swimming
 In order to prevent water from flowing
First screw the adapter into the water
assembly.

Step 1

REGULARLY VERIFY

1. The correct attachments of the mechanical parts and of the
2. The correct position, attachment and condition of the supply cables and of the insulating
parts.
3. The temperature of the motor. In the event of any excessive high, stop immediately and
have it repaired.
4. The vibration of the pump. In the case of any excessive high, stop immediately and have it
repaired.

CAUTION

Owing to the complexity of the cases covered, the instructions for installation, use and
maintenance contained in this manual do not attempt to examine all possible
cases of service and maintenance. If supplementary instructions are required or special
problems arise, do not hesitate to contact the distributor

TECHNICAL DATA

Item

CSPPS702

Input Power

685w

H. Max

32ft

Q. Max/min

273L

V

115

HZ

60

IP

IPX5

swimming pool is lower than the water inlet of the pump

flowing backward, this pump equipped a check valve.

water inlet of the pump, and then install the connector

Step 1

Step 2

1. The correct attachments of the mechanical parts and of the support screws of the pump.
2. The correct position, attachment and condition of the supply cables and of the insulating

3. The temperature of the motor. In the event of any excessive high, stop immediately and

the pump. In the case of any excessive high, stop immediately and have it

Owing to the complexity of the cases covered, the instructions for installation, use and

contained in this manual do not attempt to examine all possible and imaginable

maintenance. If supplementary instructions are required or special

contact the distributor/agent.

CSPPS703

878w
36ft
308L
115
60
IPX5

pump.

valve.

connector

support screws of the pump.

2. The correct position, attachment and condition of the supply cables and of the insulating

3. The temperature of the motor. In the event of any excessive high, stop immediately and

the pump. In the case of any excessive high, stop immediately and have it

Owing to the complexity of the cases covered, the instructions for installation, use and

and imaginable

maintenance. If supplementary instructions are required or special

6

Summary of Contents for CSPPS702












Reviews: