Cincinnati Fan HDAF Installation, Safety, Operation & Maintenance Instructions And Parts List Download

Page: 8 / 15

OMM-05-0509-page 8

Fig. 5 Vibration Severity Chart

BEFORE STARTING ANY INSPECTION OR MAINTENANCE, BE SURE BLOWER IS TURNED OFF, POWER IS

LOCKED OUT AND THE BLOWER WHEEL HAS BEEN CAREFULLY SECURED TO PREVENT WIND MILLING. IF THE

OPERATING CONDITIONS OF THE BLOWER ARE TO BE CHANGED (SPEED, PRESSURE, TEMPERATURE, ETC.)

CONSULT CINCINNATI FAN OR OUR SALES OFFICE FOR YOUR TERRITORY TO DETERMINE IF THE UNIT WILL

OPERATE SAFELY AT THE NEW CONDITIONS.

V. ROUTINE INSPECTION & MAINTENANCE

Periodic inspection of all the blower parts is the key to good maintenance and trouble-free operation. The frequency
of inspections must be determined by the user and is dependent upon the severity of the application,

BUT,

it should

NEVER

exceed a 12 month period. The user should prepare an inspection and maintenance schedule and make

sure it is adhered to.

Summary of Contents for HDAF
















Search results

Summary of Contents for HDAF

Reviews:

Related manuals for HDAF

Brands by name

Popular brands

Cincinnati Fan HDAF, Installation, Safety, Operation & Maintenance Instructions And Parts List

Search results

Summary of Contents for HDAF

Reviews:

Related manuals for HDAF

Brands by name

Popular brands