Cillit Impulsor Optronic F3 Installation And Operating Manual Download Page 14

Page: 14 / 52

1 4

Initial star

Initial startup

tup

After checking that the unit has been installed
correctly and after inspecting the current, water
and waste water (according to DIN 1988, part 4),
start the unit as described below:

Undo the childproof lock (11

11) and flip up the cap (7

7).

Run the cable of the transformer plug (1

1) through

the connection cable gland (10

10) on the rear of the

Impulsor Optronic

module and connect to the ter-

minal A

A (polarity is not important).

Plug the transformer plug (1

1) into the outlet.

ap-

pears on the display, and an audio signal is emit-
ted. These signals indicate that there is no active
substance in the unit.

Connecting the active substance container

Impulsor Optronic

module

module F3

1. Undo the childproof lock (11

11) and flip up the

cap (7

7).

2. Remove the aluminium seal from the 3kg min-

eral substance container.

3. Lift the active substance container from the

bottom above the suction pipe (8

8) and attach it

by turning it gently. The empty message goes
out, and the audio signal is switched off.

4. Flip down the cap (7

7) and screw down the child-

proof lock (11

11) to prevent the mineral substance

container from twisting.

Connect the water flow. The metering unit is now
ready to use.

Impulsor Optronic

module

module T10/T20

T10/T20

1. Undo the childproof lock (11

11) and flip up the

cap (7

7).

2. Connect the suction line (13

13) and the return line

(14

14) of the suction lance. The suction line is

marked for suction. It must be pushed onto the
nozzle with the arrow pointing inside the unit.
The return line is connected to the other noz-
zle. Secure both lines using the hose clamps
provided.

3. Insert the plug (12

12) of the suction lance (9

9) into

the socket (B

B) of the electronic controller (5

5).

4. Flip the cover (7

7) back down and screw down

the childproof lock (11

11).

5. Open the 10/20l box or canister of active sub-

stance. Remove any aluminium seals. Insert
the suction lance (9

9) into the container and

tighten the lid.
Do not lift or transport the canister by the

Do not lift or transport the canister by the

Do not lift or transport the canister by the
suction lance handle.

suction lance handle.

Connect the water flow. The metering unit is now
ready to use.

Corrosion protection in copper pipes with

Corrosion protection in copper pipes with
Impulsor Optronic

Impulsor Optronic

module

module T20 and Quantophos

T20 and Quantophos

Cu2

The objective of the procedure is to maintain wa-
ter with a pH value between 7.8 and 8.4.
The factor on the electronic controller may need
to be reprogrammed:

First, begin metering using the factory setting (fac-

fac-

tor 12

tor 12). Remove approximately 100 litres of water
from the system downstream from the metering
unit and upstream from any storage containers.
Next, collect approximately 2 litres of water in a
clean container and measure the pH using a pH
metre.

If the measured pH is less than 7.8

is less than 7.8

is less than 7.8, the factor

factor

must be moved towards “1”

must be moved towards “1” (1 water metre pulse
= 1 metering stroke).

If the measured pH is greater than 8.4

greater than 8.4

greater than 8.4, the factor

factor

must be moved towards “15”

must be moved towards “15” (15 water metre
pulses = 1 metering stroke).

Hold do

Hold down

wn the T1 and T2 keys simultaneously for

around 2.5 seconds to change the factor. The
display reads “12” (factory setting).

Use the T1 and

T1 and

T1 and T2

T2 keys to select the required

factor between “1” and “15”.

Next, hold down the T1 and

T1 and

T1 and T2 k

T2 k

T2 ke

eys sim

ys sim

ys simultane-

ultane-

ously f

ously for around 2.5 seconds

or around 2.5 seconds

or around 2.5 seconds. The new factor is

stored and the controller returns to normal op-
eration.

Keep measuring and changing the setting until
the measured pH is between 7.8 and 8.4. Flip the
cover back down and tighten the screws on the
childproof lock.