CIAT ITEX NA 10.51 D Installation, Operation, Commissioning, Maintenance Download Page 16

Document non contractuel.

Dans le souci constant d’améliorer son matériel, CIAT se réserve le droit de procéder sans

préavis à toutes modifications techniques.

Non contractual document. With the thought of material improvement always in mind,

CIAT reserves the right,without notice, to proceed with any technical modification.

Dieses Dokument ist keine Vertragsunterlage.

Da wir ständig bemüht sind, unser Material noch weiter zu verbessern, behält sich CIAT

das Recht vor, technische Änderungen ohne vorherige Ankündigung vorzunehmen.

Documento no contractual. En la preocupaciòn constante de

mejorar su material, CIAT se reserva el derecho de proceder,

sin previo aviso, a cualquier modificaciòn technica.

Documento non contrattuale. Nella preoccupazione costante di

migliorare il suo materiale, CIAT si riserva il diritto di procedere

senza preavviso a tutte le modificazioni tecniche necessarie.

Siège social

Avenue Jean Falconnier B.P. 14

01350 Culoz - France

Tel. : +33 (0)4 79 42 42 42

Fax : +33 (0)4 79 42 42 10

[email protected] - www.ciat.com

C

ompagnie 

I

ndustrielle

d’

A

pplications 

T

hermiques

S.A. au capital de 26 728 480

R.C.S. Bourg-en-Bresse B 545.620.114

Fabriqué par : CIAT Italia S.r.l.

Summary of Contents for ITEX NA 10.51 D

















Reviews: