CIAT AQUACIATPOWER ILD-HE Series, Instruction Manual

Page: 51 / 56

9 - DIAGNOSTICS
Code Description Possible cause Action taken on the unit Reset type
10043 Low Entering Water Temperature in
Heating
Low entering fluid temperature in
Heating mode
None Automatic, if water temperature
returns to normal or heating mode
is stopped
10051 Water Exchanger Flow Switch Failure
Flow switch fault Unit shuts down Manual
10063 Circuit A High Pressure Switch Failure
High pressure switch is open,
compressor fault
Circuit A shuts down Manual
10064 Circuit B High Pressure Switch Failure
High pressure switch is open,
compressor fault
Circuit B shuts down Manual
10090 Water Exchanger Flow Switch: Setpoint
Configuration Failure
Setpoint configuration failure Unit cannot be started Manual
10097 Water Exchanger Temperature Sensors
Swapped
Input and output temperature
reversed
Unit shuts down Manual
10099 Refrigerant Leakage Detection
Refrigerant leak or leak detector
defective
None Automatic, if operating conditions
return to normal
10101 DC Free Cooling Process Failure
Dry cooler fault None Automatic, if operating conditions
return to normal
11202 Water Loop : Delta Pressure Error
Low water pressure offset Pump is stopped and the unit
cannot be started
Automatic, if water pressure delta
returns to normal
11203 Water Loop : Pressure Too Low
Pump inlet pressure is below
60 kPa
Unit shuts down Automatic (if water pressure
reading returns to normal and the
alarm occurred up to 6 times in the
last 24h); otherwise, Manual
11204 Water Loop : Pump Not Started
Too low or high water pressure
reading
Water pump is stopped Automatic, if water pressure
reading returns to normal
11206 Water Loop : Pump Overload
Water loop pressure drop too low None Automatic
11207 Water Loop : Flow Too Low
Water loop pressure drop too high Water pump is stopped Automatic, if water flow reading
returns to normal
11208 Water Loop : Pressure Sensors
Crossed
Pressure sensors crossed Unit shuts down Automatic (if the alarm occurred up
to 6 occurrences in the last 24h);
otherwise, Manual
11209 Water Loop : Low Pressure Warning
Low water pressure reading None Automatic, if water pressure
reading returns to normal
10210 Low Delta Pressure Operation Failure -
cir A
Circuit running in part load with
all available compressors and low
delta pressure during operation.
Not enough capacity available /
compressor fault
Circuit A shuts down Manual
10211 Low Delta Pressure Operation Failure -
cir B
Circuit running in part load with
all available compressors and low
delta pressure during operation.
Not enough capacity available /
compressor fault
Circuit B shuts down Manual
SERVICE AND FACTORY
70nn
Illegal configuration
7001: Unit size is unknown
Incorrect unit configuration Unit cannot be started Automatic, if configuration is corrected
8000 No Factory Configuration
No factory configuration Unit cannot be started Automatic, if configuration is provided
8001 Illegal Brand Identifier
Incorrect unit configuration Unit cannot be started Automatic, if configuration is corrected
90nn Master Chiller Configuration Error
Number #1 to nn
Configuration failure Master/slave operation is disabled
and the unit returns to the stand-
alone mode
Automatic, if master/slave
configuration returns to normal or the
unit returns to the standalone mode
SERVICE MAINTENANCE WARNING
130nn Service Maintenance Alert Number # nn
004: Maintenance servicing required
Servicing action required. Contact
Manufacturer Service Agency.
Depending on the severity of the
alarm, the unit may continue to
operate or the unit shuts down
Manual
13005 Fgas check needed, call your
maintenance company
As above As above Manual
VFD DRIVE FAILURE
170nn Circuit A VFD Fan Drive Failure
Speed controller fault. See also
9.3.2 Drive alarms.
Circuit A shuts down Automatic or Manual
(motor overload only)
180nn Circuit B VFD Fan Drive Failure
As above Circuit B shuts down Automatic or Manual
(motor overload only)
350nn Circuit A VFD Fan Drive Alert
As above None Automatic
360nn Circuit B VFD Fan Drive Alert
As above None Automatic
190nn VFD Pump 1 Drive Failure
As above Unit is restarted with another
pump running. If no pumps are
available, the unit shuts down
Automatic or Manual
(motor overload only)
EN-51 AQUACIAT
POWER