Chrysler Sebring Coupe Owner'S Manual Download Page 352

Page: 352 / 394

90,000 Miles (144 000 km) or at 90 months

▫

Change engine oil and engine oil filter.

▫

Rotate tires.

MILEAGE/

MONTHS

DEALERSHIP

NAME/CODE

DATE

REPAIR

ORDER #

96,000 Miles (154 000 km) or at 96 months

▫

Check automatic transaxle fluid level.

▫

Inspect disc brake pads, rotors and calipers for
wear and leaks.

▫

Check brake hoses for deterioration or leaks.

▫

Inspect drive shaft boots for grease leaks and
damage.

▫

Change engine oil and engine oil filter.

▫

Rotate tires.

MILEAGE/

MONTHS

DEALERSHIP

NAME/CODE

DATE

REPAIR

ORDER #

102,000 Miles (163 000 km) or at 102 months

▫

Replace spark plugs, platinum-tipped type.

▫

Replace timing belt.*

: Not required if belt was previously changed.

▫

Change engine oil and engine oil filter.

▫

Rotate tires.

MILEAGE/

MONTHS

DEALERSHIP

NAME/CODE

DATE

REPAIR

ORDER #

108,000 Miles (173 000 km) or at 108 months

▫

Check automatic transaxle fluid level.

▫

Inspect disc brake pads, rotors and calipers for
wear and leaks.

▫

Check brake hoses for deterioration or leaks.

▫

Inspect drive shaft boots for grease leaks and damage.

▫

Change engine oil and engine oil filter.

▫

Rotate tires.

MILEAGE/

MONTHS

DEALERSHIP

NAME/CODE

DATE

REPAIR

ORDER #

352

MAINTENANCE

Summary of Contents for Sebring Coupe











































































































































































































































































































































































































Search results

Summary of Contents for Sebring Coupe

Reviews:

Chrysler Sebring Coupe, Owner'S Manual, Page: 352 / 394

Search results

Summary of Contents for Sebring Coupe

Reviews: