manualshive.com logo in svg

Chrysler Sebring Coupe, Owner'S Manual, Page: 350 / 394

Share
Download
Chrysler Sebring Coupe Owner'S Manual Download Page 350

!

60,000 Miles (96 000 km) or at 60 months

▫

Inspect suspension system for looseness and dam-
age.

▫

Inspect ball joint and steering linkage seals for
grease leaks and damage.

▫

Check and service exhaust system as required
(connection portion of muffler, muffler pipes and
converter heat shields).

▫

Check fuel system for leak
(tank, pipe line and connection, and fuel tank
filler tube cap).

▫

Check evaporative emission control system for
leaks and clogging (except evaporative emission
canister).

▫

Check distributor cap and rotor.

▫

Change engine oil and engine oil filter.

▫

Rotate tires.

MILEAGE/

MONTHS

DEALERSHIP

NAME/CODE

DATE

REPAIR

ORDER #

!

66,000 Miles (106 000 km) or at 66 months

▫

Change engine oil and engine oil filter.

▫

Rotate tires.

MILEAGE/

MONTHS

DEALERSHIP

NAME/CODE

DATE

REPAIR

ORDER #

!

72,000 Miles (115 000 km) or at 72 months

▫

Check automatic transaxle fluid level.

▫

Inspect disc brake pads, rotors and calipers for
wear.

▫

Check brake hoses for deterioration or leaks.

▫

Inspect drive shaft boots for grease leaks and
damage.

▫

Change engine oil and engine oil filter.

▫

Rotate tires.

MILEAGE/

MONTHS

DEALERSHIP

NAME/CODE

DATE

REPAIR

ORDER #

350

MAINTENANCE

Summary of Contents for Sebring Coupe











































































































































































































































































































































































































Reviews:

No comments