Christini AWD 450DS Service Manual Download Page 44

Page: 44 / 118

Page 43

•

Remove the 6 cover bolts with an 8mm socket or t-handle and pull
cover off of the frame.

•

To remove the chain, pull the tensioner back with a flat blade
screwdriver and pull the sprocket out with fingers or non-marring
pliers. Remove the chain from countershaft sprocket.

•

Check the following and replace if needed:

1. Sidebar bearing and cover bearing should be smooth turn-

ing.

2. Check engagement spline action by engaging and disen-

gaging switch on handle bars.

3. Sidebar seal and cover seal for wear.

4. Excessive wear on chain tension block.

Warning: Do not use an O-ring chain as there is not enough
clearance for one and it would rub the frame.

Cover and Chain Removal

Summary of Contents for AWD 450DS























































































































Search results

Summary of Contents for AWD 450DS

Reviews:

Related manuals for AWD 450DS

Brands by name

Popular brands

Christini AWD 450DS, Service Manual

Search results

Summary of Contents for AWD 450DS

Reviews:

Related manuals for AWD 450DS

Brands by name

Popular brands