Christini AWD 450DS Service Manual Download Page 23

Page: 23 / 118

Page 22

Maintenance

INTAKE VALVE:

•

Insert the feeler gauge between the valve lifter and the cam labe.

•

Check the valve clearance for the intake valves using a feeler gauge.

Valve clearance IN: 0.16+0.03mm

EXHAUST VALVE:

•

Insert the feeler gauge between the rocker arm and shim.

•

Check the valve clearance for the exhaust valves using a feeler gauge.

Valve clearance Ex: 0.28+0.03mm

VALVE CLEANCE ADJUSTMENT:

•

Remove the camshaft holder assembly

•

The shims my stick to the inside of the valve lifter.

•

Do not allow the shims to fall into the crankcase.

•

The shims can be easily removed with tweezers or a magnet.

•

Clean the valve shim contact area in the valve lifter with compressed air.

•

Measure the shim thickness and record it.

Summary of Contents for AWD 450DS























































































































Search results

Summary of Contents for AWD 450DS

Reviews:

Related manuals for AWD 450DS

Brands by name

Popular brands

Christini AWD 450DS, Service Manual

Search results

Summary of Contents for AWD 450DS

Reviews:

Related manuals for AWD 450DS

Brands by name

Popular brands