Christie Roadie 4K35 Service Manual Download Page 61

Page: 61 / 87

5. Carefully slide the anode (+) connector off the front of the lamp.
6. Hold the lamp from the cathode (-) end and carefully unscrew the lamp from the cathode

connector while supporting the anode end.

7. Remove the lamp by carefully guiding it through the reflector.

8. Immediately place the lamp inside the protective cover, or original packaging and place it in a

location where it cannot fall or get bumped.

Installing the lamp

Caution! Failure to comply with the following could result in minor or moderate injury.

•

EXPLOSION HAZARD! Handle a lamp by the cathode and anode end shafts only. Do not handle
the lamp by the glass.

•

EXPLOSION HAZARD! Do not stress the glass of a lamp or bare bulb in any way.

•

EXPLOSION HAZARD! Do not over-tighten the lamp.

1. Shut down the projector (on page 22).
2. Remove the new lamp from the protective case.

Before removing the lamp from the case, loosen the cathode (-) screw and remove the
cathode nut from the lamp.

3. If installing a lamp different than what was removed, use the table below to determine the

correct position of the anode yoke assembly:

Lamp

Type

Anode yoke position

2.0 and 3.0 kW

CDXL-20
CDXL-30

Move the lamp cradle to the rear
position, which is approximately 1”
closer to the reflector.

4.5, 6.0, and 7.0
kW

CDXL-45
CDXL-45SP
CDXL-60
CDXL-60SP
CDXL-70

Move the lamp cradle as far forward as
possible (position closest to igniter).

Parts and module replacement

Roadie 4K35 and 4K45 Service Manual

020-101694-03 Rev. 1 (01-2016)

Summary of Contents for Roadie 4K35
























































































Search results

Summary of Contents for Roadie 4K35

Reviews:

Related manuals for Roadie 4K35

Brands by name

Popular brands

Christie Roadie 4K35, Service Manual

Search results

Summary of Contents for Roadie 4K35

Reviews:

Related manuals for Roadie 4K35

Brands by name

Popular brands