manualshive.com logo in svg

Christie LED012-CP-R, Installation And Setup Manual

Share
Download
Christie LED012-CP-R Installation And Setup Manual Download Page 20

Exterior side pads with two holes

Interior pads with four holes

1. If the tiles are being mounted on an external support structure, ensure the external support

structure is anchored to the wall and/or to the floor.
The design and anchoring of the LED display structure is not the responsibility of Christie
Digital Systems USA Inc. Contact a Christie representative for structure design options.

2. Determine where the mounting pads should be installed.

a) Find the center of the bottom of the display area.
b) Position the mounting template with the bottom left template hole centered on the point

identified in step 2a.

c) Level and hang the mounting template on the support structure.

3. Insert the springs into the mounting pads.
4. Install the mounting pads.

a) Place the mounting pads inside the template holes, and secure them to the support

structure.
For installation onto a steel structure, tighten the M6 screws to a torque of 3.55 Nm
(31.42 lbs.in).
For installation onto a wooden surface:

•

M8 wood screws—Tighten to a torque of 11.5 Nm (101.8 lbs.in)

Installation and setup

Velvet LED Display System Installation and Setup Guide–CorePlus Series (Remote Power)

20

020-102423-01 Rev. 1 (06-2018)

Copyright 

©

 2018 Christie Digital Systems USA, Inc. All rights reserved.

Summary of Contents for LED012-CP-R












































Reviews:

No comments

Brands by name

Popular brands

Load more brands