manualshive.com logo in svg

Christie 1506, Product And Assembly Manual

Share
Download
Christie 1506 Product And Assembly Manual Download Page 48

Modular Series Cabinet Single, Double and Triple 

(Product numbers 1506, 1511 and 1519)

48

BARBECUE COOKTOPS

1.  CC2 Electric Barbecue Cooktop
2.  CC2 Gas Barbecue Cooktop: Natural gas, Liquid petroleum gas, or Universal LPG
3.  CC2-i Electric Smart Barbecue Cooktop
4.  CC2-i Gas Smart Barbecue Cooktop

OPTIONS

1.  Sink
2.  Additional Access Door for a storage compartment 
3.  Gas Bottle Storage Kit

GAS BOTTLE STORAGE KIT FOR DOUBLE CABINET, CONSISTING OF:

(1) x Gas bottle access door
(2) x Vertical post divider channels (factory fitted)
(1) x 9 mm Compressed fibre cement (CFC) divider panel 

GAS BOTTLE STORAGE KIT FOR TRIPLE CABINET, consisting of:

(1) x Gas bottle access door
(4) x Vertical post divider channels (factory fitted)
(2) x 9 mm Compressed fibre cement (CFC) divider panel

STANDARD PANEL COLOURS

Check our website at www.dachristie.com for current off-the-shelf finishes, standard powder 
coating colour options (lead times apply), and custom colours available at extra cost.

|  

Options and accessories

Summary of Contents for 1506

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands