manualshive.com logo in svg

Christie 1506, Product And Assembly Manual

Share
Download
Christie 1506 Product And Assembly Manual Download Page 29

Installation and User Manual 6820_00

29

4.4 Assembly and installation 

STEP 5 

1.  Remove the unsecured channel frame from the top of the posts.
2.  Identify the location of the access doors. Do not install panels into this space.
3.  Install the compressed fibre cement and stainless steel fascia panels together as a pair.
4.  With two people, lift the panels and slide them into the channel guides between two 

posts. Repeat this for all remaining panels.

Note: Stainless steel panels will have a protective film on the outer surface. Peel back 
the protective film slightly along each long edge before installing.

Gas Installations:

If your cabinet has a Gas Bottle Storage kit, locate the 9mm divider panels and pre-drill 
any services holes before proceeding. Slide the panel into place between the two facing 
channels to create a separate compartment for the gas bottles.

FIG. 18

Double cabinet assembly and installation

  |  

Summary of Contents for 1506

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands