background image

- 11 -

English

To insure safe operation, please observe following precautions :

Use (2) AA or LR6 type alkaline batteries.

Replace two batteries at same time.

Do not use a new battery with an used battery.

Avoid contact with water or liquid.

Do not expose Remote Control Unit to moisture, or heat.

Do not drop Remote Control Unit.

If a battery has leaked on Remote Control Unit, carefully wipe case clean and install new batteries.

Danger of explosion if battery is incorrectly replaced.

Dispose of used batteries according to batteries manufacturers instructions and local rules.

Pull up lid and
remove it.

Remove battery
compartment lid.

Slide batteries into
compartment.

Replace compartment lid.

Two AA size batteries

For correct polarity (+ and
–), be sure battery
terminals are in contact
with pins in compartment.

REMOTE CONTROL BATTERIES INSTALLATION

1

2

3

Operating Range 

Point Remote Control Unit toward
projector (Infrared Remote Receiver)
whenever pressing any button.
Maximum operating range for Remote
Control Unit is about 16.4’ (5m) and
60° in front and rear of a projector.

16.4’
(5 m)

16.4’
(5 m)

60°

60°

Summary of Contents for 103-011100-01

















Reviews: