Chore-Time FLEX-IR ST73000 Installation And Operating Instructions Manual Download Page 4

1.

Importance of User/Installer Manual

PLEASE READ ALL INSTRUCTIONS CAREFULLY BEFORE USE. 

SAVE THESE INSTRUCTIONS. 

The User/ Installer Manual forms an integral part of the installation, itscomponents,
equipment and devices. Furthermore:

It must be kept within immediate reach at all times, i.e. until the installation, its equipment,
components and devices are disposed of.

It must be considered a permanent part of the equipment and passed on when selling,
transferring or lending the installation, its components and devices.

Contact PigTek Pig Equipment Group should you have any questions or suggestions concerning 
the information contained in this User/Installer Manual. 

All information in this publication is based on the latest product information available at the 
time of printing. Because of our commitment to continuous improvement, PigTek Pig 
Equipment Group reserves the right to make changes to the information, products and/or 
services referenced herein at any time without notice and without incurring any obligation. 

PigTek Pig Equipment Group shall not be liable for direct, indirect, special or consequential 
damages resulting from the use of the information contained in this User/Installer Manual. 

The instructions contained in this User/Installer Manual are not intended to cover all details or 
variations in equipment and configurations, nor may it provide for every possible contingency 
concerning the installation, operation or maintenance of your equipment. Should additional 
information be required please contact your PigTek Pig Equipment Group Authorized Dealer. 

These Operating and Assembly Instructions and the information contained in them have been 
compiled with all due care. However, PigTek Pig Equipment Group does not assume any 
liability for printing errors or other errors and any damage or loss resulting from such errors. 

PigTek and Chore-Time are registered trademarks of CTB, Inc. All brand names and product 
names mentioned in this document are trademarks or registered trademarks of their respective 
holders. 

Our contact details: 

PigTek Pig Equipment 
A Group division of CTB, Inc. 
401 East Syracuse Street 

Tel. : 1 800-341-1039 

P.O. Box 2000 

Fax : 1 800-236-6118 

Milford, IN 46542 

This manual is copyrighted. No part of this manual may be photocopied or reproduced in any 
form without the prior written consent of CTB, Inc

.

© Copyright 2013 CTB, Inc. 
All rights reserved. 

Summary of Contents for FLEX-IR ST73000













Reviews: