background image

1

2

Main Use Purpose and Application Scope

NQ2 series electromagnetic starter (hereinafter referred to as starter) is mainly used in electric circuits 

with AC frequency of 50Hz (or 60Hz), rated operating voltage up to 660V and rated operating current up to 
68A  for  controlling  the  direct  start  and  stop  of  electric  motor.  Starter  with  thermal  overload  relay 
(hereinafter  referred  to  as  thermal  relay)  can  be  used  to  protect  the  overload  and  phase  loss  of  electric 
motor. 

Key Technical Parameters

01

NQ2 Series Electromagnetic Starter

Table 1 Ambient Conditions

Ambient temperature (℃) 

Hot and humid atmospheric conditions

Altitude

Pollution class/installation category

-

5℃~+40℃, average temp. not exc35℃ within 24h

+40℃, RH not exceeding 50% and may reach 90% at +20℃

No influence below 2,000m

Class 3/

Table 2 Key Technical Parameters of Starter (I)

AC-3

660V

380V

220V

Model

Conventional 

free air 

thermal 

current of 

shell frame, 

Ith (A)

Rated 

operating 

current 
of shell 

frame,

 Ie (A)

Rated power control of 

shell frame, Pe (kW)

AC 

contactor 

model 

assembed

Thermal 

relay 

model 

assembled

Setting 
current 

range of 

thermal 

relay (A)

Button 
type of 
starter 

with 

button

0.1~0.16

0.16~0.25

0.25~0.4

0.4~0.63

0.63~1

1~1.6

1.25~2

1.6~2.5

2.5~4

4~6

5.5~8

7~10

9~13

12~18

17~25

23~32

28~36

NQ2-15

□/

1

NQ2-15

□/

2

NQ2-15

□/

3

NQ2-15

□/

4

13

18

25

36

12

18

25

32

7.5

10

15

18.5

5.5

7.5

11

15

3

4

5.5

7.5

NC1-12

NC1-18

NC1-25

NC1-32

NR2-25

NR2-36

NP2-EA31

(start)

NP2-EA42

(stop)

Summary of Contents for NQ2 Series











Reviews: