background image

H04755:11/08

9

Division of Foundations Worldwide, Inc. 

7001 Wooster Pike

Medina, OH 44256  USA

Telephone: 1 877.716.2757 (U.S. Only)

or +1 330.722.5033

Fax: +1 330.722.5037

www.childcraft-furniture.com

www.foundations.com

WARNING

• 

FAILURE TO FOLLOW THESE WARNINGS AND THE ASSEMBLY INSTRUCTIONS 

COULD RESULT IN SERIOUS INJURY OR DEATH.

     

WARNING: 

Infants can suffocate on soft bedding. NEVER add a pillow 

or comforter. NEVER place additional padding under an infant.

 

Read all instructions before assembling crib. Keep instructions for future use. A pouch is 

attached to crib for permanent storage of the instructional literature.

• 

Infants can suffocate in gaps between crib sides and a mattress that is too small.

• 

To reduce the risk of SIDS pediatricians recommend healthy infants be placed on their backs 

to sleep, unless otherwise advised by your physician.

• 

To help prevent strangulation, tighten all fasteners. A child can trap parts of the body or 

clothing on loose fasteners.

• 

After raising side, make sure latches are secure (if your unit has a drop side).

• 

When child is able to climb out or reaches the height of 35 inches (90 centimeters) the crib 

shall no longer be used.

• 

DO NOT place crib near window where cords from blinds or drapes may strangle a child.

• 

If refinishing, use a non-toxic finish specified for children’s products.

• 

DO NOT leave child in crib with side lowered. Be sure side is in raised and locked position 

whenever child is in crib.

• 

When child is able to pull to standing position, set mattress to lowest position and remove 

bumper pads, large toys and other objects that could serve as steps for climbing out.

• 

NEVER use plastic shipping bags or other plastic film as mattress covers because they can 

cause suffocation.

• 

DO NOT use a water mattress with this crib.

• 

Replace teething rail(s) if damaged, cracked, or loose (if equipped with teething rails).

• 

Strings can cause strangulation! DO NOT place items with a string around a child’s neck, such 

as hood strings or pacifier cords. DO NOT suspend strings over a crib or attach strings to toys.

• 

When disassembling this crib, DO NOT remove any item attached with wood screws.

• 

Always ensure a safe environment for the child by checking regularly, before placing the child 

in the crib, that every component is properly and securely in place.

• 

Check this product for damaged hardware, loose joints, missing parts or sharp edges before and 

after assembly and frequently during use. DO NOT use crib if any parts are missing, damaged or 

broken. If any parts are missing or broken or you need assistance with assembly, DO NOT return 

the product to your dealer. Call Foundations

®

 for assistance at 1 877.716.2757 (U.S. Only) or +1 

330.722.5033 (Monday through Friday, 9:00 a.m.– 4:00 p.m. Eastern Time) for replacement parts 

and instructional literature if needed. Include model identification numbers with your request 

which you recorded on page 2. DO NOT substitute parts.

• 

Follow warnings on all products in a crib.

!

!

Summary of Contents for Crib'n'Double Bed 34801










Reviews: